This section allows you to view all Topics made by this member. Note that you can only see Topics made in areas you currently have access to.
Topics - Cold Trigger Finger
Now I have a new to me rifle in the same cartridge . But just didn't think it wise to start torching off ammo that tho was loaded to book powder charges. Those charges were max book.
First thing I needed was a good reliable bear load as spring has come a month or more early. And the punks in fur coats are probably getting ready to be out and about.
So, I pound about 100 bullets out of their homes. No small task considering I used a Lee Factory Crimp die to keep them from moving. Dump the powder, decap , anneal , trim and champfer . Then I primed a dozen as I was running short on time.
Settle on a mid book load as my temporary stopping point having already done a bit of loading starting at starting charge weights last week.
Load the dozen , go out on the back deck and torch a couple off to check for any problems.
Everything looks very good. So, I should be set.
But there is this nagging bug in my head that wants to know how fast my bullets are going. Well, the book says X is the starting velocity . And Y is the velocity at max charge weight/pressure. I'm right in the middle so Z should be the velocity of these loads.
Yup, that's what it should be. The bullets are going fast enough to do the job at hand if needed.
But it bugs me to no end not knowing pretty much exactly how fast my bullets are going.
If I had the time I could set up the chronograph and find out. But no time. Or daylight. So now I have to wait 18 hours or so to stop this from bugging me.
Anyone else suffer from chronograph data itis ?
I really like all the station holes . It indexes nice and tight. I lightly lubed it with Amsoil full synthetic 2 cycle oil . Really good stuff.
I just got it mounted on the bench. Gotta get everything adjusted then start cranking out ammo.
This will go on an AR with mil spec front sight so I will need a riser mount . Like those I listed.
There are almost Too many options !
This is the style I'm thinking about.
Thanks in advance.
My question is, what does it take to headspace the bolt correctly ?
Thanks in advance .
If so , how did the bullets do?
What vel, range, penetration , wound channel ?? Ect.
Thanks in advance.
One of my biggest requirements is for the scope to have a short eyepiece. And long enough eye relief so I can have a 13" lop on my 458 and not get ringed. This scope has 3.75" eye relief . which is a q/4" less than I prefer. But it looks short enough in the eyepiece . That the very back end of the scope shouldn't protrude much past the rear of the striker. Which is the gold standard for a rifle with a fair amount of recoil.
One reviewer was negatively commenting on the diameter of the center dot. Myself, I like that size. A bit over 1 moa. So as its a ffp it will cover 6.5 moa at 500 yards.
I would get the mil/mil version tho.
In some ways the Vortex Razor 2, 1-6 ×24 is better. Full 4" of eye relief. But the eye piece is a bit longer than I want. And, it weighs 10 oz more than the NX8.
I emailed NightForce requesting information on this scope . Asking if it is as tough as some of their NXS scopes. Will see what they say.
It doesn't come with bases and rings.
Beings the action is something of a Model 70 clone I'm wondering if it takes Model 70 bases ?
If anyone has a Kimber I would really appreciate any info.
P.S. I going to mount my 10x42 SWFA SS mil dot on it to check its accuracy and play a bit.
Not sure what scope will be my final choice. But I'm leaning towards a mid their 3-15 ffp. Probably be a couple different ones along the way.
Anyway, I've got plenty of H4350 and Rl17. . It would be AWESOME if my rifle shot them as well as it does the Berger 140 Hunting VLD. .
Might even aneal some brass and stuff.
.476" diameter, .396" meplat . .838" bullet length . 381.3 grain weight.
Should be able to push it over 1300 fps from my revolver.
Y'all NEED one , or two of these. !!!
The reason it is almost perfect. Its cromo instead of stainless.
The scope I'm interested in is the IOR Valdada 4-28×50, 40 mm tube Recon .
That rifle scope is about the same price as a Swarovski spotter. And I would get far more pleasure from a rifle scope than a spotting scope.
My friend is shooting .338 , 225 gr TSX BT factory ammo that I think is going the standard 2780 fps.
Can anyone give me the wind drift at 100 + 200 yards at 10, 20, + 30 mph with this load. I tried JBM but I don't have a good enough data connection
Thank you in advance